Graphic & Print Design · 9 min read · 1,877 words

Pull-Up Banner Sizes UK: 5 Widths, Bleed and Artwork

Pull-Up Banner Sizes UK: 5 Widths, Bleed and Artwork

What size is a pull-up banner in the UK?

The two standard UK pull-up banner sizes are 800mm and 850mm wide by 2000mm tall, with 1000mm, 1200mm and 1500mm wide versions at the same height. Set the artwork at full size plus 3mm bleed on every edge, in CMYK, as a PDF at 150 to 300dpi, and keep words clear of the bottom.

Banner size (W x H) Artwork size with 3mm bleed Listed by Typical use
800 x 2000mm 806 x 2006mm Tradeprint, instantprint, Solopress, Route1Print Shop floors, foyers, budget stands
850 x 2000mm 856 x 2006mm Tradeprint, Solopress, Route1Print The usual exhibition and premium size
1000 x 2000mm 1006 x 2006mm All four A wider message or a photo-led design
1200 x 2000mm 1206 x 2006mm All four Backdrop for a table at a show
1500 x 2000mm 1506 x 2006mm All four A single banner that fills a small stand

Sizes checked on each printer’s own product page in November 2026. Printers change their ranges, so always download the template for the exact banner and base you are ordering.

Pull-up, roller, roll-up and retractable banners are the same product: a printed sheet that winds into an aluminium base and is held up by a pole. This guide is the spec sheet: sizes, millimetres and pixels. For what to put on the banner, and how to get leads from it at a show, read our roller banner and exhibition design guide.

Pull-up banner specs by UK printer

Four large UK online and trade printers publish their roller banner specs openly. They agree on sizes and bleed, and differ on resolution and the safe zone.

Printer Widths at 2000mm tall Resolution asked for Bleed Safe zone Base allowance Lowest listed price
Tradeprint 800, 850, 1000, 1200, 1500mm 150dpi 3mm all sides 50mm from the trim edge Template is the finished size plus bleed; keep the bottom clear £31.29 ex VAT (budget cartridge, 850 x 2000mm)
instantprint 800, 1000, 1200, 1500mm 300dpi recommended, 150dpi minimum 3mm all sides 3mm in from the cut Not stated £32.16 ex VAT for one, default options
Solopress 800, 850, 1000, 1200, 1500mm, plus XL sizes up to 2000 x 3000mm 300dpi 3mm all sides Not stated on the banner page Not stated £29.99 ex VAT (800 x 2000mm)
Route1Print (trade only) 800, 850, 1000, 1200, 1500mm 300dpi minimum 3mm 3mm Added by their workflow: no extra artwork needed £29.14 ex VAT for one, default options (800 x 2000mm, standard cassette)

Prices are the “from” figures each printer showed in November 2026, before delivery and VAT, for its cheapest base. The base is where cheap banners save money, and it decides whether the banner still stands straight after a dozen shows.

Visible area vs the part hidden in the base

When a pull-up banner is extended, the graphic runs from the top rail down to the lip of the base. The bottom edge of the print never fully leaves the cassette, because it stays attached to the roller inside. So a strip at the bottom of your artwork sits at, or just inside, the lip of the base.

Printers deal with that strip in one of two ways:

  • You keep it clear. Tradeprint’s template is the finished size plus bleed, with a 50mm safe zone, and it warns that content near the bottom “can be obscured” because the banner can retract into the cartridge. Its advice is to keep URLs, social handles and QR codes away from the bottom.
  • The printer adds it. Route1Print’s specs say there is “no need to supply extra artwork or spacing to fit the cassette”, because its workflow applies the allowance automatically.

Some suppliers supply a template that is taller than the advertised banner. If yours does, the extra depth is the part that stays in the base: design to the template exactly as given, and never stretch a finished design to fill it.

There is a second, larger bottom zone to think about, and it has nothing to do with the cassette. At an event, tables, bags and people hide the lower part of a banner. Our exhibition guide puts it plainly: nothing that matters goes in the bottom 600mm. Treat the printer’s figure as the hard limit and the 600mm as the design limit.

Bleed and safe zone in millimetres

All four printers ask for 3mm of bleed on every edge. Bleed is extra background that runs past the cut line, so a slightly off-centre trim never leaves a white sliver. For an 800 x 2000mm banner, instantprint spells it out: set a custom size of 806 x 2006mm, and run the background right to the edges.

The safe zone is where the printers differ. instantprint and Route1Print ask for 3mm inside the cut. Tradeprint asks for 50mm. If you are not sure which printer will produce the banner, design to the stricter one: keep every word, logo and QR code at least 50mm in from the sides and top, and further up from the bottom. A banner designed to 50mm prints safely anywhere; one designed to 3mm does not.

What resolution does a pull-up banner need?

Here the printers genuinely disagree. Tradeprint asks for 150dpi, and its help centre says that figure stays the same across all its large-format sizes. instantprint recommends 300dpi with 150dpi as the minimum. Solopress and Route1Print ask for 300dpi.

Resolution only matters for photos and other pixel images. Text and a vector logo print sharp at any size, so keep them as vector, never flattened into a photo. The table shows how many pixels a photo needs to fill each banner at full size (excluding bleed).

Banner width Pixels needed at 150dpi Pixels needed at 300dpi
800mm 4,724 x 11,811 9,449 x 23,622
850mm 5,020 x 11,811 10,039 x 23,622
1000mm 5,906 x 11,811 11,811 x 23,622
1200mm 7,087 x 11,811 14,173 x 23,622
1500mm 8,858 x 11,811 17,717 x 23,622

A photo filling only the top third needs only a third of the height. To check a photo, divide its pixel width by the width it will print at in inches (millimetres divided by 25.4). Under 150, it will look soft up close.

Colour mode and file format

  • CMYK, not RGB. Every printer above asks for CMYK. Route1Print notes that RGB and Pantone colours are converted during proofing, so a bright screen colour can come out duller. If a brand colour matters, ask for a proof.
  • PDF first. All four accept a print-ready PDF. Tradeprint’s spec points to PDF/X-1a:2001. instantprint and Route1Print also take JPEG.
  • Fonts outlined or embedded. A missing font is one of the most common reasons printers reject artwork.
  • One banner per page. Ordering several designs? Tradeprint asks for one multi-page PDF, or one PDF per banner.

Minimum text size and line weight

Tradeprint recommends a minimum font size of 18pt and a minimum line weight of 2pt on roller banners. That is a print floor, not a design target: 18pt is fine for small print on a banner read from arm’s length, and far too small for a headline. A headline needs to read across an aisle, which is why our exhibition guide works with 80pt and above. Fine lines under 2pt can break up or vanish on banner material, so thin borders and hairline icons are best avoided; the wider checks are in our UK print-ready artwork guide.

Which pull-up banner size suits you, by situation

  • Shop floor, reception or foyer: 800 or 850mm. It fits beside a door or counter and is the cheapest to replace.
  • A trade stand with a table: 850mm as a pair, or one 1200mm behind the table, so your message clears the table top.
  • A small stand with no backdrop: 1500mm, or an XL size, gives you a wall from one base.
  • A counter or desk: Solopress lists desktop roller banners in A4 and A3 (210 x 297mm and 297 x 420mm).
  • Seen from both sides: double-sided banners exist (Solopress and instantprint both list them), each side its own artwork file.

Buy for the space you use most often, not the biggest show of the year.

Six steps to set up a pull-up banner file: template, size plus 3mm bleed, safe zone, photo resolution, CMYK PDF and a full-scale proof check.
Most banner reprints trace back to skipping step one: the printer's own template.

Setting up the file: the steps

  1. Download the printer’s template for the exact width and base you are ordering.
  2. Set the document at the finished size plus 3mm bleed on every edge (806 x 2006mm for an 800mm banner).
  3. Run the background to the bleed edge, and keep every word inside the safe zone, well clear of the bottom.
  4. Check photos at 100% against the pixel table above.
  5. Convert to CMYK and outline the fonts, then export a print-ready PDF.
  6. Check the proof at full scale, from across the room.

Artwork mistakes that cause reprints

  • An A4 file scaled up. The proportions are wrong (A4 is about 1:1.41, a pull-up banner 1:2.35 to 1:2.5), so something gets stretched or cropped.
  • A web address, phone number or QR code at the very bottom, where the base or the crowd hides it.
  • A logo that only exists as a small JPG. At two metres tall it turns fuzzy. Our Recreate & Vectorise service redraws it as true vector artwork, £79 for one layout.
  • RGB colours that look neon on screen and print flat. More on why in why printer colours do not match your screen.
  • No bleed, so the background stops short of the cut.

Pull-up banner design and print costs

The print and base start at around £29 to £32 before VAT and delivery at the printers above, rising with a better cassette, a wider banner or double-sided printing. Design is separate. Our Poster & Banner Design service is £89: built as vector, supplied as a print-ready PDF in CMYK with bleed, plus the editable source file and a print specs sheet, with a first draft within 48 hours of the brief. We design to your printer’s template, and we do not print, so you keep the choice of printer. Every price we charge is on our pricing page.

Pull-up banner, PVC banner or poster?

A pull-up banner is for indoors: events, receptions and shop floors. For a fence, a scaffold or a shop front outdoors, you need a PVC or mesh banner with hems and eyelets, covered in our PVC banner design guide. For a window or wall, a poster is cheaper; see the poster design guide.

Sources

All checked November 2026. Printers update their specs and prices; the template supplied with your order is the final word.

Free resource

Get the UK Print-Ready Artwork Checklist (free)

A one-page checklist for any UK designer or printer covering CMYK, bleed, fonts and resolution. Saves you the pre-press fix-up fees.

No spam. UK GDPR compliant. We only use your email to send this resource, unless you tick the box to hear from us.

Frequently asked questions

What is the standard size of a pull-up banner in the UK? +

The two standard sizes are 800mm and 850mm wide by 2000mm tall. UK printers such as Tradeprint, Solopress and Route1Print also list 1000mm, 1200mm and 1500mm widths at the same 2000mm height, and Solopress offers XL sizes up to 2000 x 3000mm. Desktop versions come in A4 and A3.

How much of a pull-up banner is hidden in the base? +

A strip at the bottom always sits at or inside the lip of the base, because the print stays attached to the roller. Tradeprint asks for a 50mm safe zone and warns that content near the bottom can be obscured. Route1Print adds the cassette allowance itself. If a template is taller than the banner, the extra is the hidden part.

What resolution should pull-up banner artwork be? +

Between 150 and 300dpi at full size, depending on the printer. Tradeprint asks for 150dpi; instantprint recommends 300dpi with 150dpi as the minimum; Solopress and Route1Print ask for 300dpi. Resolution only applies to photos. Text and vector logos print sharp at any size, so keep them as vector rather than flattening them into an image.

What bleed does a roller banner need? +

3mm on every edge. Tradeprint, instantprint, Solopress and Route1Print all ask for it. For an 800 x 2000mm banner that means a document of 806 x 2006mm, with the background running right to the edge. Keep words and logos inside the safe zone, which is between 3mm and 50mm in from the cut depending on the printer.

What file format do printers want for a pull-up banner? +

A print-ready PDF in CMYK, with fonts outlined or embedded, at the exact size of the printer's template plus bleed. Tradeprint points to PDF/X-1a:2001, while instantprint and Route1Print also accept JPEG. Send one PDF per banner, or one multi-page PDF if you are ordering several designs at once.

How much does it cost to have a pull-up banner designed? +

Our Poster & Banner Design service is £89. You get vector artwork supplied as a print-ready PDF in CMYK with bleed, the editable source file and a print specs sheet, with a first draft within 48 hours of the brief. We design to your chosen printer's template. Printing is separate, from about £30 before VAT at the printers in this guide.

Work With Us

Need help with your brand or website?

Luxbranding is a UK online creative agency. Fixed prices, unlimited revisions, 48-hour start. Logo design from £129, websites from £299.

Ask Us a Question

Reply within one working day · No commitment